Check out the new Tape Project website at tapeproject.com, now with online ordering. Inventory is updated every week, so stop by often to see what we have in stock.

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - stellavox

Pages: 1 2 [3] 4 5 ... 16
31
Events / Re: Happy New Year! Big changes coming
« on: January 02, 2015, 02:39:02 PM »
Hey Doc - Best to you and the QUEEN

Charles (King)

32
General Discussion / Merry Christmas / Happy Holidays Tapesters!!
« on: December 22, 2014, 05:27:04 AM »
be WELL and Continue to Enjoy the MUSIC!

33
Tape Tech / Re: What causes the warbled sound on tape? (reel to reel)
« on: December 01, 2014, 09:12:14 AM »
You might try cleaning the pinch roller.  How old / long since you used the deck?  Roller could have hardened up or not be making enough contact / pressure with the capstan.  Or is the supply reel binding up and causing a "back pressure" on the tape?

Charles

34
Tape Tech / Denon DH150 schematic needed
« on: November 18, 2014, 07:47:57 AM »
Want to see how the remote control socket is wired internally.

Thanks!

Charles

35
General Discussion / Re: Analog Album Advice...
« on: November 14, 2014, 08:58:12 AM »
Nick,

Where do you live - asking so we might be able to put you in touch with some "locals" either with similar interests or could help you out "directly"

Charles

36
A customer sent me a Teac AN-180 for "upgrading".  This activity allowed me to "update my understanding of" Dolby B decoders in general, this Teac, and an Advent 100A that I happened to have in my "to do" pile.

Most of these "stand alone" decoders were designed to "plug in" between your tape recorder and your system's preamplifier / control section and decode a pre-recorded tape that was encoded with Dolby B noise reduction.   

The "upgrades" consisted of replacing 3 or 4 coupling capacitors in the input stages of the decoding section and adding regulation to the power supplies.  The Teac  had a "first generation op amp" in the output section which I bypassed.  The output amplifier in the Advent was discrete so I left it in.

Listened to both finished units and slightly preferred the Advent.  Sent both to the customer, and he did also.  He may keep it - or it's "up for grabs".

Charles

 

37
Steve,

It was there! Much Thanks

Charles

38
Tape Tech / Teac AN-180 or AN-80 service manual / schematics needed
« on: May 28, 2014, 12:47:01 PM »
Mainly the schematics

Thanks

Charles

39
Reel to Reel Tape Machines / Re: Newbe from Ohio
« on: April 20, 2014, 05:25:50 AM »
Welcome!

And your name is....

Let us know if you need any help (or encouragement) - reasonably friendly folks here...

Charles

40
General Discussion / Re: I REMEMBER WHEN ............
« on: April 20, 2014, 05:23:25 AM »
NICE Post Bob!

THANKS

41
Reel to Reel Tape Machines / Re: New member, just wanted to say hi.
« on: January 27, 2014, 06:57:48 AM »
Welcome aboard Spiros

Charles

42
Reel to Reel Tape Machines / Re: Technics RS-1500 with flourescent VUs
« on: January 27, 2014, 06:55:17 AM »
Where do you plan to fit them?  Why Studer bias coils.

Charles

43
General Discussion / Re: Early Stereo Tapes
« on: January 26, 2014, 09:52:12 PM »
See "2 track era" in the pre-recorded tapes thread, starting Nov 30,2011

Charles

44
General Discussion / Re: To all of my wonderful friends here
« on: January 04, 2014, 07:09:03 AM »
Happy and Healthy (and prosperous even) New Year to all. 

Enjoy; find solace, comfort and peace with your music in WHATEVER form you listen.

However, tape isn't a bad choice.

Keep your heads clean and your tails out!

Charles

45
Tape Tech / Re: Dolby B decoder "troubles"
« on: November 20, 2013, 06:31:28 AM »
Steve,

How you doin' buddy?!!  Were you at RMAF - if so, missed you.

Regarding your comments on consumer decoders - and for others going this route - all the "B" decoders had to use the same "Dolby approved" circuit.  The components they used were up to them - and economics dictated.  As many DIY'ers have found, swapping out the coupling electrolytic caps in the signal path typically makes a BIG improvement.   And there is some GREAT sound on those Barkley-Crockers!

Keep up your great "tapester" work!

Charles

Pages: 1 2 [3] 4 5 ... 16