Check out the new Tape Project website at tapeproject.com, now with online ordering. Inventory is updated every week, so stop by often to see what we have in stock.

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Listens2tubes

Pages: 1 2 [3] 4 5 ... 19
31
Tape Project Machines / Flux Magnetics Heads
« on: December 18, 2014, 09:34:44 PM »
Are Flux Magnetics heads still being made?

32
I have a MkIII-8. Locate the internal speed switch on the main board. I am not sure why this machine shares this switch with it B2 cousins but it does. Get the deck on it's side and spray contact cleaner (Deoxit) through the switch while working it back and forth 10 or more times. Also spray into the back corners of the front Speed switch and work it 30+ times. This treatment shook out capstan and logic issues on my MkIII-8. Also I have found the Pitch Control can cause wow and occasionally keep the capstan from spinning if dirty. Exercising it On and Off (in/out) 30-40 times has helped there. I wish mine was a 2 track.

33
I'll try to dig into my BII-HD to see if the board matches.

34
Reel to Reel Tape Machines / Re: MX5050BII manuals at The Analog Dpet.
« on: August 25, 2014, 06:15:04 PM »
That site rocks! Thanks Dan!

35
On my BII models dirty switches are usually the main cause of problems. Try cleaning the Speed switches, on front and the main board as well as the Reel (Large-Small) switch, exercise the Pitch Control knob(in and out) and Monitor switches. That H - L switch on the main board controls more than just speed and can be the fix for some of the weirdest combination of maladies. Had a machine that a tech said the capstan motor was defective. Cleaned the H - L  switch and the capstan works fine. For that internal H-L switch you will need the main board swung down, then turn the machine on it's side, spray DeOxit into the side of the switch while working it.

36
General Discussion / Re: Birth of the 3M M56
« on: August 07, 2014, 07:27:55 PM »
Steve you've done it again! That was a great read. Thank you so much.

37
Try cleaning the internal speed (L-H on the main board) as well. I have solved many problems just by cleaning that switch.

38
Events / Re: Listening party at the studio, SF
« on: July 08, 2014, 06:23:52 PM »
Dang! You guys have to do one of these events in the NY/NJ area!


Please post pictures and comments.:-)

39
Prerecorded Tapes / Re: Oscar Peterson Tapes
« on: May 22, 2014, 05:59:43 PM »
199.00 Euros = US $?

40
General Discussion / Re: Axpona 2014
« on: May 15, 2014, 07:40:22 PM »
Thanks Myles. Lots of interesting info in a short period of time. I hope there can be a Reel Talk at the New York show.  Only gripe: Too bad they didn't pass a wireless mic around to the attendees to let us hear the questions they were asking. 

41
General Discussion / Re: Axpona 2014
« on: April 25, 2014, 08:20:01 PM »
Will it be filmed? I would love to be able to experience this.

42
Same here, just a blank page.

43
Tape Tech / Re: Just got a A77 MKIII - mods & tweaks
« on: February 15, 2014, 07:14:45 PM »
I recently saw HS boards for an A77 on ebay. Not sure if the seller also was offering the capstan. From what I have read it is not so simple as just a simple parts change. Voltages are also different in the HS version.

44
Reel to Reel Tape Machines / Re: Revox repair in Northern Ireland?
« on: January 11, 2014, 05:07:43 PM »
You should also try posting on http://www.tapeheads.net/ there are a few techs in the UK.

45
General Discussion / Re: To all of my wonderful friends here
« on: January 04, 2014, 09:41:51 PM »
I think you'll like them.

Pages: 1 2 [3] 4 5 ... 19